Dell Wyse 3030 LT, 4GF / 2GF

MODEL NO:N06D

PART NO:00061

HSID:646A9X7LCF

PROD ID:ASSY,CHAS,4GBF/2GBR,TPM,3030LT

Specifications

The basic specs for my 3030 LT are:

Processor
Type    Speed	Intel Celeron N2807 Dual Core 1.6GHz
Memory
Flash    RAM	4GB (eMMC soldered down)   2GB (soldered down)
Video
Chip    Max resolution	Intel HD Graphics 2560 x 1600 32-bit colour (Display Port) 1920 x 1200 32 bit colour (DVI via adaptor) 2560 x 1600 32-bit colour (VGA via adaptor)
Ports
Video    Network    USB    Serial    Parallel    PS/2	2 x Display Port 10/100/1000 3 x USB2.0 1 x USB3.1 0 0 0
Power
Plug    Off    Idle    Running	Coax 5.5mm/2.1mm 0W 2.5W 3W
Dimensions
H x W x D (mm)	187 x 29 x 117 (without stand) 198 x 69 x 117 (with stand)

The 3030 LT runs Linux and is fitted with 4GB of flash and 2GB of DDR3 RAM.

Power Supply

My 3030 LT came with a 12V 2.5A Chicony PSU. Despite what is mentioned in some data sheets the back panel is clearly marked +12V by the power socket. (Subsequent models may use a 19V supply). The connector is a standard coax plug: 5.5mm/2.1mm.

The power consumption is low (<6W) so you do not need a particularly highly rated power supply. Out of interest I did try out a (ex router?) 9V/2A 'Wall Wart' style power unit with the 3290. The 3290 apparently ran without any problems.

Getting Inside

If you need to do this is it is fairly straightforward. You need to remove the foot (if fitted) which is a push fit. Then remove the three screws on the back panel. You then need to gently lever off the side panel that covers the top of the PCB. Start at the two back corners as the internal metalwork on the front edge actually slides under a lip just behind the front panel. When you get it clear at the back you need to move the panel towards the rear to clear this lip. On re-assembly you need to remember that you need to locate the front edge under this lip before pushing the side panel back on.

CPU

For those to whom it matters here is some detail from Linux's /proc/cpuinfo. (Dual Core Processor)

vendor_id	:	GenuineIntel
cpu family	:	6
model	:	55
model name	:	Intel(R) Celeron(R) CPU N2807 @ 1.58GHz
stepping	:	8
flags	:	fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer rdrand lahf_lm 3dnowprefetch epb tpr_shadow vnmi flexpriority ept vpid tsc_adjust smep erms dtherm ida arat

PCI

Expansion

Expansion of the 3030 LT is limited, there is little room inside the housing and the Flash and RAM memory are soldered to the board. Click on the photo right for a larger version.

Flash: The flash is a 4GB eMMC chip soldered to the bottom of the board.

RAM: The RAM is a 2GB DDR3 L RAM with a 1.333 MT/s data transfer rate. It is soldered to the top of the board just under the edge of the heatsink.

mPCIe: There is a mPCIe socket for a wireless module. The PCB is clearly marked WLAN by it and there are two mounting holes on the rear panel for the antenna. As you can see no Wireless card was fitted to my example.

mSATA: There is an unpopulated mSATA area on the PCB. Whether it is a simple matter of soldering in the appropriate connector to use this I have no idea.

USB: There is a single USB 2.0 port on the rear and three ports on the front panel, the top one of which is to the 3.1 USB standard.